| 982752701 Liebherr A954B Li Slewing Ring | d:15 mm; Mass bushing:0.022 kg; Specific static load factor K0:20 N/mm²; Tolerance housing:H7; Permissible sliding velocity v min.:0.25 m/s; Tolerance shaft:h8; Coefficient of friction µ max.:0.1; Coefficient of friction µ min.:0.05; D:22 mm; Permissible sliding velocity v max.:5 m/s; Specific dynamic load factor K:10 N/mm²; B:16 mm; |
| 982757401 Liebherr R974 Slewing Ring | d:17 mm; Mass inner ring:0.011 kg; B:16 mm; r, r1,2 min.:0.3 mm; F:20 mm; |
| 982751301 Liebherr R904 Slewing Ring | Calculation factor f2B:1.02; Calculation factor f2C:1.05; ra max.:1.5 mm; Calculation factor e:0.68; Db max.:136 mm; Ball diameter Dw:15.875 mm; Static axial stiffness, preload class D:575 N/µm; Preload class C GC:1840 N; Calculation factor f2A:1; Preload class D GD:3680 N; Basic dynamic load rating C:74.1 kN; Calculation factor f2D:1.08; da max.:104.8 mm; r3,4 min.:1 mm; Calculation factor fHC:1; |
| 933628601 Liebherr A944C Li Slewing Ring | Basic static load rating C0:13.2 kN; Sealing system:5-lip seal on flange; Housing material:Sheet steel; Purpose/ Application:Seeding; N:6.7 mm; Minimum rotational disc speed min.:100 r/min; Maximum disc diameter max.:500 mm; Recommended maximum temperature max.:50 °C; b:2 mm; Recommended lower temperature limit for storage (static):-50 °C; D1:55 mm; Corrosion protection:Zinc-coated housing; |
| 933816501 Liebherr A934B Li Slewing Ring | B:20.5 mm; Mass inner ring:0.027 kg; d:20 mm; r, r1,2 min.:0.3 mm; F:25 mm; |
| 90205146 Liebherr R922 LC Slewing Ring | Oil Speed Rating n2:13000 rpm; Accessories:Two Shields & Snap-R; d:20.000 mm; Basic Dynamic Radial Load Rating C:20500 N; Sealed Speed Rating n3:9000 rpm; Grease Speed Rating n1:9000 rpm; Fillet Radius ra:1.00 mm; Basic Static Radial Load Rating Co:17000 N; D:47.0000 mm; B:20.60 mm; |
| 982882001 Liebherr A310 Slewing Ring | J min.:250.825 mm; J max.:279.4 mm; Initial grease fill:110.56 g; da:76.2 mm; R2:22.225 mm; End plug (suffix Y):EPR 9; R1:53.975 mm; Cap bolt, SAE grade:8; Housing:SAFS 517; Mass pillow block:24.5 kg; Cap bolt:2 x 5/8-11 UNC; Bearing limiting speed:5600 r/min; H2:38.1 mm; ba:35.719 mm; PG:1/8 NPT; H:187.325 mm; A2:127 mm; Pa:9.25 kN; P90°:47.2 kN; RG:3/8 NPT; |
| 982752701 Liebherr R954B Slewing Ring | Calculation factor f2C:1.05; D:170 mm; Calculation factor f1:1; B:28 mm; Preload class A GA:420 N; Basic static load rating C0:108 kN; d:110 mm; Calculation factor f:1.14; Calculation factor fHC:1.02; Mass bearing:1.63 kg; Preload class B GB:840 N; Ball diameter Dw:19.05 mm; r1,2 min.:2 mm; Fatigue load limit Pu:3.9 kN; db min.:119 mm; ra max.:2 mm; a:32.9 mm; Db max.:165 mm; Preload class D GD:3360 N; |
| 90205146 Liebherr R922 XLC Slewing Ring | Basic Static Radial Load Rating Co:125000 N; D:150.0000 mm; B:66.70 mm; Fillet Radius ra:2.00 mm; Accessories:No Shield, no Seal,; Basic Dynamic Radial Load Rating C:153000 N; Grease Speed Rating n1:2800 rpm; Oil Speed Rating n2:3800 rpm; Sealed Speed Rating n3:2800 rpm; d:70.000 mm; |
| 982752101 Liebherr R944B Slewing Ring | B:150 mm; Fatigue load limit Pu:455 kN; s1 max.:32.6 mm; da max.:513 mm; Misalignment factor k1:0.12; Basic dynamic load rating C:3800 kN; Basic static load rating C0:6400 kN; Da min.:544 mm; da min.:438 mm; Da max.:602 mm; Reference speed:800 r/min; r1,2 min.:5 mm; Operating clearance factor k2:0.1; ra max.:4 mm; D1 ≈:571 mm; Mass bearing:150 kg; d:420 mm; Limiting speed:1100 r/min; Ca min.:2.2 mm; |
| 982751901 Liebherr A914C li Slewing Ring | Basic Dynamic Radial Load Rating C:30700 N; Basic Static Radial Load Rating Co:15000 N; d:20.000 mm; Accessories:Without Accessories; Fillet Radius ra:1.00 mm; Grease Speed Rating Open/Shielded n1:10000 rpm; Oil Speed Rating Open/Shielded n2:13000 rpm; Sealed Speed Rating n3:7300 rpm; B:19.00 mm; D:72.0000 mm; |
| 982751301 Liebherr A314 Li Slewing Ring | Specific dynamic load factor K:25 N/mm²; Permissible sliding velocity v max.:0.5 m/s; Mass bushing:0.016 kg; d:9 mm; Coefficient of friction µ max.:0.15; D:14 mm; B:12 mm; Tolerance housing:H7; Permissible sliding velocity v min.:0 m/s; Coefficient of friction µ min.:0.08; Tolerance shaft:e7; Specific static load factor K0:45 N/mm²; |